Gigabit Ethernet 13 Port Basic

Key Features:

Gigabit Ethernet 13 Port Basic-Switch Profi Line Modular

A new 13 port switch designed to offer not only the top performance but also the flexibility to be used in confined spaces. In addition the switch is modular which means it enables expansions depending on the needs which minimize the initial cost of the switch to minimum necessary.

– Gigabit performance with Energy-Efficient Ethernet
– Power-over-Ethernet+ (802.3at),maximum of 30 W per port
– Extended temperature range
– Compact metal housing for DIN rail assembly
– Robust design, extension modules available
– Redundant power inputs
– Linux kernel, open standards, long-term availability
– SD card for firmware and configuration
– Fault tolerance with minimum recovery times

Product Details

General
Type Gigabit Ethernet Switch Layer 2+, IEEE 802.3 compliant, fanless
Performance Store-and-forward, Full wire-speed, non-blocking on all ports
MAC-Adresses 8,192 addresses, automatic learning and aging
Jumbo Frames max. 10,240 bytes
VLANs Tagging IEEE 802.3ac
Priorisation IEEE 802.1p
VLAN IDs 0..4095
256 VLANs
Static and dynamic VLAN table
Quality of Service 4 hardware-queues per port prioritisation according to:
* IPv4/IPv6
* VLAN priority IEEE 802.1p
* port
queue weighting strict or weighted, configurable
Management CLI: telnet, ssh
Web: http, https
SNMPv1, SNMPv2c, SNMPv3
Microsens NMP-Software
Serial Interface (RJ-45)

 

Local Ports (Twisted-Pair)
Number of Ports 9 + 4(Combo-Ports)
Type Gigabit Ethernet, triple speed 10/100/1000Base-T
Connector RJ-45 jack, shielded
Cable Type Twisted-Pair cable, category 5e, impedance 100 Ohm, length max. 100 m
Flow Control Pause frames (IEEE 802.3x), configurable
Pinout Auto MDI/MDI-X, auto polarity
Power-over-Ethernet 8x Power Sourcing Equipment (PSE) IEEE 802.3at and 802.3af class 0, max. 30 W, forced-mode (legacy-devices), max. 200 W total power
1x Powered Device (PD) IEEE 802.3at and 802.3af class 0, max. 30 W, forced-mode (legacy-devices)

 

Uplink (Pluggable Transceiver)
Number of Ports 4 (Combo-Ports)
Type Fast/Gigabit Ethernet, 100/1000Base-X
Connector SFP-Slot
Flow Control Pause frames (IEEE 802.3x), configurable

 

 Uplink (Fixed Optical Transceiver)
Number of Ports 4 (Combo-Ports)
Type Gigabit Ethernet
Multimode: 1000Base-SX
Single Mode: 1000Base-LX
Connector ST or SC duplex
Fiber Cable Type Multimode: 50 or 62.5/125 µm fiber
Single Mode: 9/125 µm fiber
Distance Multimode: 550 m
Single Mode: 10 km, 20 km (optional)
actual distance may depend on fiber performance
Output Optical Power Multimode 850nm:
-9,5..-4 dBm
Single Mode 1310nm 10 km:
-9,5..-3 dBm
Single Mode 1310nm 20 km:
-9,5..+3 dBm
Receiver Sensitivity Multimode 850nm:
-18 dBm (max. 0 dBm)
Single Mode 1310nm 10 km:
-20 dBm (max. -3 dBm)
Single Mode 1310nm 20 km:
-23 dBm (max. -3 dBm)
Flow Control Pause frames (IEEE 802.3x), configurable

 

Display
Type 10 LEDs (RGB-LED)
Power Local ports 1 to 9:
green: PoE sourcing
blue: PoE+ active
orange: PoE standby
red: PoE error
Link Local ports 1 to 8:
blinking: activity
green: authorized/forwarding
orange: blocked
red: unauthorized
Status Switch Status (S)
green: device readyStatus
blinking: activity
green: authorized/forwarding
orange: blocked
red: unauthorizedPower Downlink (P)
green:  PoE sourcing
blue:     PoE+ active
orange: PoE standby
red:       PoP errorRing: Switch configured for ring mode
RM:    Ring Master (only in ring mode)Signal (in/out):
red: Alarm

 

Power Supply (DC)
Input Voltage 2x 44..57 VDC (54 VDC typ.), redundant Power
For 802.at services 54VDC (min.) is required.
Power Consumption Typ. 9 W (device only), max. 200 W (incl. PoE+)
Connector 2x 3 pin screw clamp, PE/-/+
AWG 16

 

 Environment
Operating Temperature -40..+75 °C
Storage Temperature -40°..85°C
Relative Humidity 5% to 90% non condensing

 

Mechanical
Dimensions 120.5 mm x 77.7 mm x 100.5 mm (h x w x d)

 

Standards Compliance
CE Mark 2004/108/EC (EMC)
2006/95/EG (Low Voltage)
Safety EN 60950-1:2011-1
Electromagnetic Emission EN 55022:2011-12
Electromagnetic Immunity EN 55024:2011-09
IEEE (Ethernet) 802.3i 10Base-T
802.3u 100Base-T
802.3z 1000Base-X
802.3ab 1000Base-T
802.3az Energy Efficient Ethernet
802.3x Flow Control
802.3ac VLAN Tagging
802.3af PoE
802.3at PoE+
802.1AB LLDP
802.1D Spanning Tree
802.1Q Tagged VLANs
802.1p Packet Prioritisation
802.1w Rapid Spanning Tree
802.1X Network Access Control
Other EN 50121-4:2006 (railway applications – electromagnetic compatibility)
EN 50125-3:2003 (railway applications – environmental conditions)
IEC 61850-3 (electrical substation automation)
IEEE 1613 (electric power substations)

 

SOLUTIONS

NEWSLETTER