Gigabit Ethernet 7 Port Switch

Key Features:

Gigabit Ethernet 7 Port Switch Profi Line +

A 7 port Gigabit Ethernet switch designed with extreme compact dimensions. The Performance and security both in network and access security made this switch suited for high availability areas, such as industrial automation, traffic information and control systems, as well as energy technology.
• Gigabit performance with Energy-Efficient Ethernet
• Power-over-Ethernet+ (802.3at), maximum of 30 W per port
• Extended temperature range
• Compact & robust metal housing for DIN rail assembly
• Redundant power inputs
• SD card for firmware and configuration
• Fault tolerance with minimum recovery times

Product Details

General


Type Gigabit Ethernet Switch Layer 2+, IEEE 802.3 compliant, fanless
Performance Store-and-forward, Full wire-speed, non-blocking on all ports
MAC-Adresses 8,192 addresses, automatic learning and aging
Jumbo Frames max. 10,240 bytes
VLANs Tagging IEEE 802.3ac
Priorisation IEEE 802.1p
VLAN IDs 0..4095
256 VLANs
Static and dynamic VLAN table
Quality of Service 4 hardware-queues per port prioritisation according to:
* IPv4/IPv6
* VLAN priority IEEE 802.1p
* port
queue weighting strict or weighted, configurable
Management CLI: telnet, ssh
Web: http, https
SNMPv1, SNMPv2c, SNMPv3
Microsens NMP-Software
Serial Interface (RJ-45)

Local Ports (Twisted-Pair)


Number of Ports 5 + 2(Combo-Ports)
Type Gigabit Ethernet, triple speed 10/100/1000Base-T
Connector RJ-45 jack, shielded
Cable Type Twisted-Pair cable, category 5e, impedance 100 Ohm, length max. 100 m
Flow Control Pause frames (IEEE 802.3x), configurable
Pinout Auto MDI/MDI-X, auto polarity
Power-over-Ethernet 4x Power Sourcing Equipment (PSE) IEEE 802.3at and 802.3af class 0, max. 30 W, forced-mode (legacy-devices), max. 200 W total power 1x Powered Device (PD) IEEE 802.3at and 802.3af class 0, max. 30 W, forced-mode (legacy-devices)

Uplink (Pluggable Transceiver)


Number of Ports 2 (Combo-Ports)
Type Fast/Gigabit Ethernet, 100/1000Base-X
Connector SFP-Slot
Flow Control Pause frames (IEEE 802.3x), configurable

Display


Type 10 LEDs (RGB-LED)
Power Local ports 1 to 9:
green: PoE sourcing
blue: PoE+ active
orange: PoE standby
red: PoE error
Link Local ports 1 to 8:
blinking: activity
green: authorized/forwarding
orange: blocked
red: unauthorized
Status

Switch Status (S)
green: device ready

Status
blinking: activity
green: authorized/forwarding
orange: blocked
red: unauthorized

Power Downlink (P)
green: PoE sourcing
blue: PoE+ active
orange: PoE standby
red: PoP error

Ring: Switch configured for ring mode
RM: Ring Master (only in ring mode)

Signal (in/out):red: Alarm

Power Supply (DC)


Input Voltage 2x 44..57 VDC (54 VDC typ.), redundant Power
For 802.at services 54VDC (min.) is required.
Power Consumptionn Typ. 9 W (device only), max. 200 W (incl. PoE+)
Connector 2x 3 pin screw clamp, PE/-/+AWG 16

Environment


Operating Temperature -40..+75 °C
Storage Temperature -40°..85°C
Relative Humidity 5% to 90% non condensing

Mechanical


Dimensions 120.5 mm x 77.7 mm x 100.5 mm (h x w x d)

Standards Compliance


CE Mark 2004/108/EC (EMC)
2006/95/EG (Low Voltage)
Safety EN 60950-1:2011-1
Electromagnetic Emission EN 55022:2011-12
Electromagnetic Immunity EN 55024:2011-09
IEEE (Ethernet) 802.3i 10Base-T
802.3u 100Base-T
802.3z 1000Base-X
802.3ab 1000Base-T
802.3az Energy Efficient Ethernet
802.3x Flow Control
802.3ac VLAN Tagging
802.3af PoE
802.3at PoE+
802.1AB LLDP
802.1D Spanning Tree
802.1Q Tagged VLANs
802.1p Packet Prioritisation
802.1w Rapid Spanning Tree
802.1X Network Access Control
Other EN 50121-4:2006 (railway applications – electromagnetic compatibility)
EN 50125-3:2003 (railway applications – environmental conditions)
IEC 61850-3 (electrical substation automation)
IEEE 1613 (electric power substations)
SOLUTIONS