Specifications
RipEX2
Key Features:
• CE and FCC certification for 256QAM
(1.7 Mb/s @ 300 kHz, 167 kb/s @ 25 kHz)
• Multiple Radio Protocols => Highest Network throughput
• Standard IP routing even on Radio channel
• Dynamic routing
• IPsec end-to-end security
• Wi-Fi Management, Responsive Web Interface
• Each unit tested in Climatic Chamber
• Base, Repeater and Remote use Same HW
• mPCIe Expansion Slot
• -40 to +70°C operating temperature
Technical Specifications
Radio parameters | |
Frequency bands | 135 – 175 MHz |
Channel spacing | 6.25; 12.5; 25; 50; 100; 150; 200; 250; 300 kHz |
Frequency stability | ±0.5 ppm |
Modulation | QAM: 256QAM; 64QAM; 16DEQAM; D8PSK; π/4DQPSK; DPSK |
FEC (Forward Error Correction) | 2/3; 3/4; 5/6; Off |
Gross data rate (data speed) | ||
Channel spacing | Gross data rate (modulation rate) | |
6.25 | 42 | |
12.5 | 83 | |
25 | 167 | |
50 | 333 | |
100 | 555 | |
150 | 925 | |
200 | 1111 | |
250 | 1389 | |
300 | 1736 | |
Transmitter | |
RF Output power | QAM: 0.1 – 5.0 W (20 – 37 dBm) RMS in 1dB |
Duty cycle | Continuous |
Rx to Tx Time | < 2 ms @ 6.25 kHz channel |
Intermodulation Attenuation | > 40 dBm, > 70 dBm (with external circulator / isolator) |
Spurious Emissions (Conducted) | < -36 dBm |
Radiated Spurious Emissions | < -36 dBm |
Adjacent channel power | < -60 dBc |
Transient adjacent channel power | < -60 dBc |
Receiver | ||
Sensitivity | -117 dBm (12.5 kHz; 2CPFSK; BER 10-6; 3/4 FEC) | |
Anti-aliasing Selectivity | 56 kHz @ -3 dB BW applicable for 6.25; 12.5; 25 kHz | |
Tx to Rx Time | < 2 ms @ 6.25 kHz channel | |
Maximum Receiver Input Power | 20 dBm (100 mW) | |
Rx Spurious Emissions (Conducted) | < -57 dBm | |
Radiated Spurious Emissions | < -57 dBm | |
Blocking or desensitization | > -23 dBm @ 1 MHz | |
Spurious response rejection | > 70 dB |
Technical parameters are subject to change without prior notification. | |
1) Network throughput varies and depends heavily on the data structure, optimization effectivity, protocol on Radio channel, network topology, signal budgets and many other parameters of the network. Practical tests are recommended. | |
2) Available only in Bridge mode. | |
3) Max peak envelope power (PEP) 10 W (40 dBm) . | |
Electrical | ||
Primary power | 10 to 30 VDC, negative GND | |
Rx | 8 W / 13.8 V | |
Tx | 12 – 55 W | |
Sleep mode | 0.01 W | |
Save mode | 5 W | |
Interfaces | |||
Ethernet | 10/100/1000Base-T Auto MDI/MDIX | 4× RJ45 | |
SFP | 10/100/1000Base-T or 1000Base-SXor 1000Base-LX power consumption 1.25 W | 1× SFP | |
COM | RS232 / RS485 SW configurable | DB9F | |
600 b/s – 1 Mb/s | |||
USB | USB 3.0 | Host A | |
Antenna | 50 Ω 2×SW configurable | TNC female | |
Inputs/Outputs | 1× HW alarm input1× HW alarm output | Power connector | |
2× DI, 2× DO, 1× difDInot available when Expansion board ‘C’ | RJ45 | ||
Optional interfaces | |
Expansion board ‘G’ | Active antenna 3.3 VDC SMA female |
72-channel u-blox M8 engine GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1I, Galileo E1B/C, SBAS L1 C/A: WAAS, EGNOS, MSAS, GAGAN | |
Expansion board ‘C’ | COM2: |
Expansion board ‘E’, ‘P’, ‘A’ Cellular | |
Indication LEDs | |
LED panel | 5× tri-color status LEDs (SYS, AUX, RX, TX, COM) |
ETH | 4× RJ45 (Link and Activity LEDs), 1× SFP (Status LED) |
Environmental | |
IP Code (Ingress Protection) | IP41, IP42, IP52 |
MTBF (Mean Time Between Failure) | > 900 000 hours (> 100 years) |
Operating temperature | −40 to +70 °C ( −40 to +158 °F) |
Operating humidity | 5 to 95 % non-condensing |
Storage | −40 to +85 °C ( −40 to +185 °F) / 5 to 95 % non-condensing |
Mechanical | ||
Casing | Rugged die-cast aluminium | |
Dimensions | H × W × D: 60 × 185 × 125 mm (2.34 × 7.2 × 4.9 in) | |
Weight | 1.55 kg (3.4 lbs) | |
Mounting | DIN rail, L-bracket, Flat-bracket, 19″ Rack chassis | |
SW | ||
Operating modes | Bridge / Router | |
Radio channel protocols | Transparent @ Bridge | |
User protocols on COM | DNP3, DF1, IEC101, Modbus RTU, PR2000, RDS, | |
User protocols on Ethernet | Modbus TCP, IEC104, DNP3 TCP, Comli TCP, Terminal server… | |
Serial to IP convertors | DNP3 / DNP3 TCP, Modbus RTU / Modbus TCP | |
Protocol on Radio channel | ||
Multi master applications | Yes | |
Report by exception | Yes | |
Collision Avoidance Capability | Yes | |
Remote to Remote communication | Yes | |
Addressed and acknowledged | Yes | |
Data integrity control | CRC 32 | |
Optimization | Intelligent payload data and header (Eth / IP / TCP / UDP) compression | |
Security | ||
Management | HTTPS (own certificate), SSH | |
Role-based access control (RBAC) | 4 levels (Guest, Tech, SecTech, Admin) | |
WiFi management access (optional) | WPA2-PSK secured | |
Encryption | AES256-CCM | |
VPN | IPsec, GRE | |
VLAN | IEEE 802.1Q (tagging), Q-in-Q for Transparent mode | |
AAA protocol | RADIUS | |
Firewall | Layer 2 – MAC, Layer 3 – IP, Layer 4 – TCP/UDP | |
FW | Digitally signed | |
HW tamper | Case opening evidence | |
Diagnostic and Management | ||
Link testing | ICMP ping | |
Status informations | User interfaces | |
Statistics | Historical and differential statistics for Rx / Tx Packets on all user interfaces (ETH 1-5, COM 1-3, TS 1-5) and Radio interface – for individual connections. | |
Statistics history | Several weeks | |
Event log | Events filtered by time, severity, user, remote IP address and type of event | |
SNMP | SNMPv1, SNMPv2c, SNMPv3 | |
NTP | Client / Server | |
Monitoring | Real time analysis of all interfaces (RADIO, ETH 1-5 , COM 1-3, TS 1-5) and internal interfaces between software modules | |
Standards | ||
CE | RED; RoHS; WEEE | |
FCC, IC | FCC Part 90, IC RSS-119 | |
Spectrum | ETSI EN 302 561 V2.1.1 | |
EMC | ETSI EN 301 489-1 V2.2.3 | |
Product safety | EN 62368-1:2014 + A11:2017 | |
RF health safety | EN 62311:2008 | |
Electric power substations | IEEE 1613:2009 | |
Hazardous locations | EN 60079-0:2012 | |
Environmental | EN 61850-3: 2014 | |
Vibration & shock | EN 60068-2-6:2008 | |
Seismic qualification | EN 60068-2-27:2010 | |
IP rating | EN 60529:1993 + A1:2001 + A2:2014 | |
Downloads
- ripex2-man-en Download
