Gigabit Ethernet 7 Port Switch Profi Line +
A 7 port Gigabit Ethernet switch designed with extreme compact dimensions. The Performance and security both in network and access security made this switch suited for high availability areas, such as industrial automation, traffic information and control systems, as well as energy technology.
• Gigabit performance with Energy-Efficient Ethernet
• Power-over-Ethernet+ (802.3at), maximum of 30 W per port
• Extended temperature range
• Compact & robust metal housing for DIN rail assembly
• Redundant power inputs
• SD card for firmware and configuration
• Fault tolerance with minimum recovery times
| Type | Gigabit Ethernet Switch Layer 2+, IEEE 802.3 compliant, fanless |
| Performance | Store-and-forward, Full wire-speed, non-blocking on all ports |
| MAC-Adresses | 8,192 addresses, automatic learning and aging |
| Jumbo Frames | max. 10,240 bytes |
| VLANs | Tagging IEEE 802.3ac Priorisation IEEE 802.1p VLAN IDs 0..4095 256 VLANs Static and dynamic VLAN table |
| Quality of Service | 4 hardware-queues per port prioritisation according to: * IPv4/IPv6 * VLAN priority IEEE 802.1p * port queue weighting strict or weighted, configurable |
| Management | CLI: telnet, ssh Web: http, https SNMPv1, SNMPv2c, SNMPv3 Microsens NMP-Software Serial Interface (RJ-45) |
| Number of Ports | 5 + 2(Combo-Ports) |
| Type | Gigabit Ethernet, triple speed 10/100/1000Base-T |
| Connector | RJ-45 jack, shielded |
| Cable Type | Twisted-Pair cable, category 5e, impedance 100 Ohm, length max. 100 m |
| Flow Control | Pause frames (IEEE 802.3x), configurable |
| Pinout | Auto MDI/MDI-X, auto polarity |
| Power-over-Ethernet | 4x Power Sourcing Equipment (PSE) IEEE 802.3at and 802.3af class 0, max. 30 W, forced-mode (legacy-devices), max. 200 W total power 1x Powered Device (PD) IEEE 802.3at and 802.3af class 0, max. 30 W, forced-mode (legacy-devices) |
| Number of Ports | 2 (Combo-Ports) |
| Type | Fast/Gigabit Ethernet, 100/1000Base-X |
| Connector | SFP-Slot |
| Flow Control | Pause frames (IEEE 802.3x), configurable |
| Type | 10 LEDs (RGB-LED) |
| Power | Local ports 1 to 9: green: PoE sourcing blue: PoE+ active orange: PoE standby red: PoE error |
| Link | Local ports 1 to 8: blinking: activity green: authorized/forwarding orange: blocked red: unauthorized |
| Status |
Switch Status (S) Status Power Downlink (P) Ring: Switch configured for ring mode Signal (in/out):red: Alarm |
| Input Voltage | 2x 44..57 VDC (54 VDC typ.), redundant Power For 802.at services 54VDC (min.) is required. |
| Power Consumptionn | Typ. 9 W (device only), max. 200 W (incl. PoE+) |
| Connector | 2x 3 pin screw clamp, PE/-/+AWG 16 |
| Operating Temperature | -40..+75 °C |
| Storage Temperature | -40°..85°C |
| Relative Humidity | 5% to 90% non condensing |
| Dimensions | 120.5 mm x 77.7 mm x 100.5 mm (h x w x d) |
| CE Mark | 2004/108/EC (EMC) 2006/95/EG (Low Voltage) |
| Safety | EN 60950-1:2011-1 |
| Electromagnetic Emission | EN 55022:2011-12 |
| Electromagnetic Immunity | EN 55024:2011-09 |
| IEEE (Ethernet) | 802.3i 10Base-T 802.3u 100Base-T 802.3z 1000Base-X 802.3ab 1000Base-T 802.3az Energy Efficient Ethernet 802.3x Flow Control 802.3ac VLAN Tagging 802.3af PoE 802.3at PoE+ 802.1AB LLDP 802.1D Spanning Tree 802.1Q Tagged VLANs 802.1p Packet Prioritisation 802.1w Rapid Spanning Tree 802.1X Network Access Control |
| Other | EN 50121-4:2006 (railway applications – electromagnetic compatibility) EN 50125-3:2003 (railway applications – environmental conditions) IEC 61850-3 (electrical substation automation) IEEE 1613 (electric power substations) |
